Official Reference Guide
Siser HTV Cut Settings & Application Instructions
Complete reference for all Siser heat transfer vinyl products — cut settings for every major cutter and step-by-step application instructions.
EasyWeed®
StandardSiser EasyWeed®
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 5–10g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 6
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 80–90g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 8–9g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron between Cotton and Linen
- Cover with PTFE sheet or parchment paper
- Press on flat, hard surface (not ironing board)
- Medium/firm pressure for 10–15 seconds
- Peel carrier Hot or Cold
🔥 Heat Press
- Preheat garment 2–3 seconds
- 305°F / 150°C (EasyPress: add ~30°F)
- Medium pressure for 10–15 seconds
- Peel carrier Hot or Cold
🧺 Laundering
- Wait 24hrs
- Wash warm or cold
- Normal dry
- No bleach/dry clean
- Inside out
EasyWeed® Electric
SpecialtySiser EasyWeed® Electric
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 5–10g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 6
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 80–90g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 8–9g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron between Cotton and Linen
- Cover with PTFE or parchment paper
- Press on flat, hard surface
- Medium/firm pressure for 10–15 seconds
- Peel carrier Hot or Cold
🔥 Heat Press
- Preheat garment 2–3 seconds
- 305°F / 150°C (EasyPress: add ~30°F)
- Medium pressure for 10–15 seconds
- Peel carrier Hot or Cold
🧺 Laundering
- Wait 24hrs
- Wash warm or cold
- Normal dry
- Inside out
EasyWeed® EcoStretch™
StretchSiser EasyWeed® EcoStretch™
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 5–10g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 6
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 80–90g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 8–9g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron on Cotton
- Cover with PTFE or parchment paper
- Press on flat, hard surface
- Medium pressure for 10–15 seconds
- Peel carrier Hot
🔥 Heat Press
- Preheat garment 2–3 seconds
- 250°F / 120°C (EasyPress: add ~30°F)
- Medium pressure for 10–15 seconds
- Peel carrier Hot
🧺 Laundering
- Wait 24hrs
- Wash cold
- Dry low
- Inside out
EasyWeed® Extra
Nylon-CompatibleSiser EasyWeed® Extra
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 5–10g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 6
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 80–90g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 8–9g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron between Cotton and Linen
- Cover with PTFE or parchment paper
- Press on flat, hard surface
- Medium/firm pressure for 10–15 seconds
- Peel carrier Hot or Cold
🔥 Heat Press
- Preheat garment 2–3 seconds
- 305°F / 150°C (EasyPress: add ~30°F)
- Medium pressure for 10–15 seconds
- Peel carrier Hot or Cold
🧺 Laundering
- Wait 24hrs
- Wash cold
- Dry low
- Inside out
EasyWeed® Stretch
StretchSiser EasyWeed® Stretch
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 5–10g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 6
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 80–90g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 8–9g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron between Cotton and Linen
- Cover with PTFE or parchment paper
- Press on flat, hard surface
- Medium/firm pressure for 10–15 seconds
- Peel carrier Hot or Cold
🔥 Heat Press
- Preheat garment 2–3 seconds
- 305°F / 150°C (EasyPress: add ~30°F)
- Medium pressure for 10–15 seconds
- Peel carrier Hot or Cold
🧺 Laundering
- Wait 24hrs
- Wash cold
- Dry low
- Inside out
EasyWeed® Sub Block
Sublimation BlockingSiser EasyWeed® Sub Block
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 5–10g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 6
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 80–90g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 8–9g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron between Cotton and Linen
- Cover with PTFE or parchment paper
- Press on flat, hard surface
- Medium/firm pressure for 10–15 seconds
- Peel carrier Hot or Cold
🔥 Heat Press
- Preheat garment 2–3 seconds
- 265°F / 130°C (EasyPress: add ~30°F)
- Medium pressure for 10–15 seconds
- Peel carrier Hot or Cold
🧺 Laundering
- Wait 24hrs
- Wash cold
- Dry low
- Inside out
EasyWeed® Adhesive
AdhesiveSiser EasyWeed® Adhesive
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 5–10g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 5–6
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 70–90g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 8–9g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron between Cotton and Linen
- Cover with PTFE or parchment paper
- Press on flat, hard surface
- Medium/firm pressure for 10–15 seconds
- Peel carrier Hot
🔥 Heat Press
- Preheat garment 2–3 seconds
- 275°F / 135°C (EasyPress: add ~30°F)
- Medium pressure for 10–15 seconds
- Peel carrier Hot, then apply top layer
🧺 Laundering
- Wait 24hrs
- Wash cold
- Dry low
- Inside out
Easy® Puff
Specialty — Heat Press OnlySiser Easy® Puff
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 5–10g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 6
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 90–100g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 8–9g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
⚠️ Home iron is not recommended. Easy® Puff withstands only ONE heat application — repeated pressing permanently flattens the puff. Apply Easy Puff last when layering.
🔥 Heat Press Only
- Preheat garment 2–3 seconds
- 280°F / 138°C
- Medium pressure for 8–10 seconds
- Peel carrier Hot
🧺 Laundering
- Wait 24hrs
- Wash cold
- Dry low
- Inside out
Easy® Puff Glitter
Specialty — Two-Press RequiredSiser Easy® Puff Glitter
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 35–45g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade
Setting: Glitter Mesh Iron On
Setting: Glitter Mesh Iron On
Cricut Maker
Blade: AutoBlade
Setting: Glitter Mesh Iron On
Setting: Glitter Mesh Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 5/4 | Force: 30/25
Material: Heat Transfer Glitter | Speed: 8
Material: Heat Transfer Glitter | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: 4
Cut Speed: 5 | Half Cut: 4
Roland® GX/GS-24
Blade: 45° | Force: 150–200g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 15–20g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
⚠️ Requires two presses. Layering and home iron not recommended. Apply last when layering.
🔥 Heat Press (Two Presses Required)
- Preheat garment 2–3 seconds
- 310°F / 155°C (EasyPress: add ~30°F)
- Medium pressure for 2–3 seconds
- Peel carrier Warm or Cold
- Cover & press again for 10–15 seconds
🧺 Laundering
- Wait 24hrs
- Wash cold
- Dry low
- Inside out
Easy® Puff Metallic
Specialty — Two-Press RequiredSiser Easy® Puff Metallic
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 10–20g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 6
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 90–100g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 9–10g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
⚠️ Requires two 10-second presses. Home iron not recommended. Apply last when layering.
🔥 Heat Press (Two Presses Required)
- Preheat garment 2–3 seconds
- 280°F / 138°C
- Medium pressure for 10 seconds
- Peel carrier Hot
- Cover & press again for 10 seconds
🧺 Laundering
- Wait 24hrs
- Wash cold
- Dry low
- Inside out
Easy® Glow
Glow in the DarkSiser Easy® Glow
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 5–15g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 6
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 90g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 8–9g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron between Cotton and Linen
- Cover with PTFE or parchment paper
- Press on flat, hard surface
- Medium pressure for 15 seconds
- Peel carrier Warm or Cold
🔥 Heat Press
- Preheat garment 2–3 seconds
- 305°F / 105°C (EasyPress: add ~30°F)
- Medium pressure for 15 seconds
- Peel carrier Warm or Cold (5–10 sec off press)
🧺 Laundering
- Wait 24hrs
- Wash cold
- Dry low
- Inside out
EasyReflective®
ReflectiveSiser EasyReflective®
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 5–10g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 6
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 80–90g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 8–9g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron between Cotton and Linen
- Cover with PTFE or parchment paper
- Press on flat, hard surface
- Medium/firm pressure for 10–15 seconds
- Peel carrier Warm
🔥 Heat Press
- Preheat garment 2–3 seconds
- 305°F / 105°C (EasyPress: add ~30°F)
- Medium pressure for 15 seconds
- Peel carrier Warm (wait 15+ sec off press)
🧺 Laundering
- Wait 24hrs
- Wash warm or cold
- Dry low
- Inside out
Aurora®
Cold Peel RequiredSiser Aurora®
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 30–35g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Light Cardstock
Setting: Light Cardstock
Cricut Maker
Blade: AutoBlade, Standard
Setting: Light Cardstock
Setting: Light Cardstock
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 14
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 130–140g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 8–9g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron between Cotton and Linen
- Cover with PTFE or parchment paper
- Press on flat, hard surface
- Medium/firm pressure for 15 seconds
- Peel carrier Completely Cold
🔥 Heat Press
- Preheat garment 2–3 seconds
- 305°F / 150°C (EasyPress: add ~30°F)
- Medium pressure for 15 seconds
- Peel carrier Completely Cold
🧺 Laundering
- Wait 24hrs
- Wash cold
- Dry low
- Inside out
PureHT™
StandardSiser PureHT™
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 5–8g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 6
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 80–90g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 8–9g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron on Cotton (Linen if iron runs cold)
- Cover with PTFE or parchment paper
- Press on flat, hard surface
- Medium pressure for 10–15 seconds
- Peel carrier Hot
🔥 Heat Press
- Preheat garment 2–3 seconds
- 275°F / 135°C (EasyPress: add ~30°F)
- Medium pressure for 15 seconds
- Peel carrier Hot
🧺 Laundering
- Wait 24hrs
- Wash cold
- Dry low
- Inside out
Brick® 600
Thick — Special Blade RequiredSiser Brick® 600
⚠️ Roland GX/GS-24 & Graphtec: Use 60° blade only — 45° blade is NOT recommended. Extend blade significantly on Roland.
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 25–37g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Light Cardstock+
Setting: Light Cardstock+
Cricut Maker
Blade: AutoBlade, Standard
Setting: Cardstock
Setting: Cardstock
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 7 | Force: 20
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade 7
Cut Speed: 1 | Cut Pressure: 2
Cut Speed: 1 | Cut Pressure: 2
Roland® GX/GS-24
Blade: 60°* | Force: 150–190g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 60°* | Force: 8–9g
Tool: CB09U+0 | Speed: 25 cm/s
Tool: CB09U+0 | Speed: 25 cm/s
🏠 Home Iron
- Set iron between Cotton and Linen
- Cover with PTFE or parchment paper
- Press on flat, hard surface
- Medium/firm pressure for 20 seconds
- Peel carrier Cold
🔥 Heat Press
- Preheat garment 2–3 seconds
- 310°F / 155°C (EasyPress: add ~30°F)
- Medium pressure for 20 seconds
- Peel carrier Cold
🧺 Laundering
- Wait 24hrs
- Wash cold
- Dry low
- Inside out
Glitter
GlitterSiser Glitter HTV
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 30–35g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Glitter Iron On
Setting: Glitter Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Glitter Iron On
Setting: Glitter Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 4 | Force: 11
Material: Heat Transfer Glitter | Speed: 8
Material: Heat Transfer Glitter | Speed: 8
Brother Scan N Cut DX
Blade: 3
Cut Speed: 5 | Half Cut: 5
Cut Speed: 5 | Half Cut: 5
Roland® GX/GS-24
Blade: 45° | Force: 180–190g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 17–18g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron between Cotton and Linen
- Cover with PTFE or parchment paper
- Press on flat, hard surface
- Medium/firm pressure for 10–15 seconds
- Peel carrier Warm
🔥 Heat Press
- Preheat garment 2–3 seconds
- 320°F / 160°C (EasyPress: add ~30°F)
- Medium pressure for 10–15 seconds
- Peel carrier Warm
🧺 Laundering
- Wait 24hrs
- Wash warm or cold
- Dry low
- Inside out
DiamondDust™
Glitter — CPSIA CertifiedSiser DiamondDust™
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 30–35g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Glitter Iron On
Setting: Glitter Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Glitter Iron On
Setting: Glitter Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 4 | Force: 11
Material: Heat Transfer Glitter | Speed: 8
Material: Heat Transfer Glitter | Speed: 8
Brother Scan N Cut DX
Blade: 3
Cut Speed: 5 | Half Cut: 5
Cut Speed: 5 | Half Cut: 5
Roland® GX/GS-24
Blade: 45° | Force: 180–190g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 17–18g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron between Cotton and Linen
- Cover with PTFE, parchment, or butcher paper
- Press on flat, hard surface (not ironing board)
- Medium/firm pressure for 15–20 seconds
- Peel carrier Warm (preferred) or cold
- Lift areas: re-press 5–10 sec under cover sheet
🔥 Heat Press
- Cover with PTFE, parchment, or butcher paper
- Preheat garment 2–3 seconds
- 305°F / 150°C (EasyPress: add ~30°F)
- Medium pressure for 15–20 seconds
- Peel carrier Warm (preferred) or cold
🧺 Laundering
- Wait 24hrs
- Wash cold, mild detergent
- Tumble dry low
- No dry clean
- No liquid softener
Holographic
Cold Peel RequiredSiser Holographic HTV
ℹ️ Holographic Rainbow Pearl finish varies by garment color — looks different on dark vs. light garments.
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 25–32g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Light Cardstock
Setting: Light Cardstock
Cricut Maker
Blade: AutoBlade, Standard
Setting: Light Cardstock
Setting: Light Cardstock
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 14
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: 3
Cut Speed: 5 | Cut Pressure: 5
Cut Speed: 5 | Cut Pressure: 5
Roland® GX/GS-24
Blade: 45° | Force: 150–190g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 17g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron between Cotton and Linen
- Cover with PTFE or parchment paper
- Press on flat, hard surface
- Medium/firm pressure for 10–15 seconds
- Peel carrier Cold
🔥 Heat Press
- Preheat garment 2–3 seconds
- 320°F / 160°C (EasyPress: add ~30°F)
- Medium/firm pressure for 15–20 seconds
- Peel carrier Cold
🧺 Laundering
- Wait 24hrs
- Wash warm or cold
- Dry low
- Inside out
Metal
Cold Peel RequiredSiser Metal HTV
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 5–10g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 6
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 80–90g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 9–10g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron between Cotton and Linen
- Cover with PTFE or parchment paper
- Press on flat, hard surface
- Medium/firm pressure for 10–15 seconds
- Peel carrier Cold
🔥 Heat Press
- Preheat garment 2–3 seconds
- 305°F / 150°C (EasyPress: add ~30°F)
- Medium pressure for 10–15 seconds
- Peel carrier Cold
🧺 Laundering
- Wait 24hrs
- Wash cold
- Dry low
- Inside out
Sparkle™
ShimmerSiser Sparkle™
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 10–15g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 6
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 80–90g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 9–10g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron between Cotton and Linen
- Cover with PTFE or parchment paper
- Press on flat, hard surface
- Medium/firm pressure for 10–15 seconds
- Peel carrier Hot or Cold
🔥 Heat Press
- Preheat garment 2–3 seconds
- 305°F / 150°C (EasyPress: add ~30°F)
- Medium/firm pressure for 15–20 seconds
- Peel carrier Hot or Cold
🧺 Laundering
- Wait 24hrs
- Wash cold
- Dry low
- Inside out
StripFlock® Pro
FlockSiser StripFlock® Pro
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 20–25g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Iron On/Everyday Iron On
Setting: Iron On/Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3–4 | Force: 6
Material: Heat Transfer Flocked | Speed: 5
Material: Heat Transfer Flocked | Speed: 5
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: 4
Cut Speed: 5 | Half Cut: 4
Roland® GX/GS-24
Blade: 45° | Force: 80–120g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 8–9g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron between Cotton and Linen
- Cover with PTFE or parchment paper
- Press on flat, hard surface
- Medium/firm pressure for 10–15 seconds
- Peel carrier Warm
🔥 Heat Press
- Preheat garment 2–3 seconds
- 311°F / 155°C (EasyPress: add ~30°F)
- Medium pressure for 10–15 seconds
- Peel carrier Warm
🧺 Laundering
- Wait 24hrs
- Wash warm or cold
- Dry low
- Inside out
Twinkle™
GlitterSiser Twinkle™
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 33–37g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Glitter Cardstock (one pass)
Setting: Glitter Cardstock (one pass)
Cricut Maker
Blade: AutoBlade, Standard
Setting: Glitter Cardstock (one pass)
Setting: Glitter Cardstock (one pass)
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 4 | Force: 11
Material: Heat Transfer Glitter | Speed: 8
Material: Heat Transfer Glitter | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: 4
Cut Speed: 5 | Half Cut: 4
Roland® GX/GS-24
Blade: 45° | Force: 130–160g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 13g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron between Cotton and Linen
- Cover with PTFE or parchment paper
- Press on flat, hard surface
- Medium/firm pressure for 15 seconds
- Peel carrier Warm
🔥 Heat Press
- Preheat garment 2–3 seconds
- 305°F / 150°C (EasyPress: add ~30°F)
- Medium/firm pressure for 15 seconds
- Peel carrier Warm
🧺 Laundering
- Wait 24hrs
- Wash cold
- Dry low
- Inside out
Vernice
Hang Dry OnlySiser Vernice
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 5–10g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 6
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 80–90g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 9–10g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
🏠 Home Iron
- Set iron between Cotton and Linen
- Cover with PTFE or parchment paper
- Press on flat, hard surface
- Firm pressure for 20 seconds
- Peel carrier Hot or Cold
🔥 Heat Press
- Preheat garment 2–3 seconds
- 320°F / 160°C (EasyPress: add ~30°F)
- Firm pressure for 20 seconds
- Peel carrier Hot or Cold
🧺 Laundering
- Wait 24hrs
- Wash cold
- ⚠️ Hang dry only
- Inside out
EasySubli®
SublimationSiser EasySubli®
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 15–20g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: Standard
Setting: Iron On/Everyday Iron On
Setting: Iron On/Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 15
Material: Heat Transfer, Smooth | Speed: 8
Material: Heat Transfer, Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 80–90g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 8–9g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
EasyPatterns® Plus
PatternedSiser EasyPatterns® Plus
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 5–10g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Everyday Iron On
Setting: Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 6
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 80–90g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 8–9g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
EasyColor™ DTV®
Direct-to-VinylSiser EasyColor™ DTV®
✂ Cut Settings
Romeo® & Juliet™
Blade: 45° | Force: 5–10g
Offset: 0.250 | Speed: 10
Offset: 0.250 | Speed: 10
Cricut Explore Air
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Cricut Maker
Blade: AutoBlade, Standard
Setting: Vinyl+/Everyday Iron On
Setting: Vinyl+/Everyday Iron On
Silhouette Cameo® 4 & 5
Blade: AutoBlade, 3 | Force: 6
Material: Heat Transfer Smooth | Speed: 8
Material: Heat Transfer Smooth | Speed: 8
Brother Scan N Cut DX
Blade: AutoBlade
Cut Speed: 5 | Half Cut: Auto
Cut Speed: 5 | Half Cut: Auto
Roland® GX/GS-24
Blade: 45° | Force: 80–90g
Offset: 0.250 | Speed: 30–50 cm/s
Offset: 0.250 | Speed: 30–50 cm/s
Graphtec®
Blade: 45° | Force: 8–9g
Tool: CB09U+0 | Speed: 30 cm/s
Tool: CB09U+0 | Speed: 30 cm/s
Important: All settings are suggested starting points. Adjust based on blade condition, cutting strip wear, and mat age. Always perform a test cut before production. Settings sourced from official Siser NA documentation (July & September 2025).
Download printable versions: Cut Settings PDF | Application Instructions PDF
Download printable versions: Cut Settings PDF | Application Instructions PDF